✕
☰

The future of manufacturing: MES to manage extreme vertical integration

For manufacturers of sophisticated and fast-changing products, the need to move from paper-based processes to an intelligent manufacturing execution system (MES) is, arguably, not just necessary to drive efficiency and quality into value chains, but a basic need if the business is to stay relevant in the marketplace. 

The first challenge in implementing an MES is to align very clearly with long-range strategic objectives and key results. There should be no doubt about the key benefits MES will deliver to manufacturing, how the project will be run, or how success will be measured. Challenge number two is to decide on a sustainable project approach and methodology that allows for quick wins, followed by continuous improvement and rapid scaling for years into the future. The third challenge is to educate key stakeholders and decide which low-risk manufacturing processes might be geared to a “paper-on-glass” implementation—as well as processes which require a fully-integrated MES implementation.

Once implementation is aligned to objectives and key results, then project methodology and MES risk-based approach are known. After that, a more detailed scope and pilot project planning can be undertaken to define a pilot model of an end-to-end value stream with significant volume, process characteristics, and product variety. This will demonstrate the potential of the MES to the wider business. The pilot should include, at minimum, the manufacturing model, IT and OT integrations, and (for regulated industries) a validation process. 

Finally, a dedicated team of exemplary people is essential to a successful MES pilot and to the subsequent enterprise-wide roll-out. Plan to invest heavily in team education and training during the pilot phase.

MES ensures all plant activities are visible, managed and measured. Companies managing extreme vertical integration have complex and varied manufacturing operations, where a product of one operation, work cell, or department, is a component to the next. That’s exactly what leading oral health product manufacturer, Ultradent Products, Inc. has done.

Case study: Ultradent

Based in Utah, USA, Ultradent prides itself on extreme vertical integration to deliver products used by dentists in over 120 countries. Providing a wide range of dental solutions, the Ultradent plant incorporates several in-house manufacturing departments including chemistry formulation, weighing, dispensing, primary package filling, secondary packaging, injection moulding, laboratory, CNC machining, assembly, printing, and other operations. Its production lines are both high volume / low mix and low volume / high mix. Ultradent also creates specialty and customised products for its customers that have a limited shelf life. As a result, traceability, genealogy, and first expired first out (FEFO) material handling at every process step are crucial to manufacturing operations.

After 40 years of business using paper-based systems, Ultradent made the strategic decision to move to an MES and fully electronic batch records. To narrow down potential suppliers, it started by looking at companies with experience in the medical sector. It looked for functional fit, configurability, extensibility, and the ability to customise. The complexity of manufacturing also required a system with a model-centric approach to enable integration with a variety of other systems on site. With highly capable IT and engineering teams in house, it was further looking for a partner who would also act as a systems integrator and provide Ultradent with greater visibility and input into the roadmap for the MES.

Craig Pinegar, director of manufacturing IT at Ultradent, said: “Finding the right partner was crucial for us. We have excellent in-house capabilities and knew we would want and need to customise the MES. We selected Critical Manufacturing after a comprehensive review of systems available and a great deal of research into what MES can do.”

Project selection was the first critical step for the Ultradent/Critical Manufacturing project team. Ultradent wanted a minimal viable product that would cover the end-to-end value stream of a product line that was representative of at least half of the business. Selection took time and a great deal of discussion. The next step was incredibly detailed project planning, considering IT and OT integrations to support work order management, material management, labelling, optical verification, and scale integration. The factory and processes were modelled in the MES with a focus on manufacturing execution, data collection, and exception management.

Detailed vertical integration

Ultradent worked in close partnership with Critical Manufacturing. The team decided that PLM functions and document management would remain in PLM while planning, scheduling, inventory, and cost management would remain in the ERP system. The MES would need to synchronise with the PLM, ERP, labelling, and more than 30 custom services using REST APIs and JSON messaging handled by middleware and message queuing. For Level 2  integration, (per ISA-95, the automation layer) drivers were configured in the MES to communicate with IPCs, PLCs and other instrumentation using OPC-UA.

Pinegar continued: “After one year, we reached our first milestone with the ‘minimal viable product’ pilot line up and running and gathering data we could have only dreamed about. Our second milestone was a minimal scalable product. Robust change management is the next big challenge ahead. We can have as many as 500 affected documents and items on pending change orders at any given time.”

One of Ultradent’s primary goals was to convert paper process steps and data collection points into electronic in the MES. Thus, the change management workload and complexity are critical drivers for the MES. 

Pinegar said: “Without great change management capability within the MES, managing changes to the factory product and process model can be both time-consuming and error-prone. We are currently working closely with Critical Manufacturing to design and implement enhancements to facilitate high volume change management along with other improvements in areas such as weighing, dispensing, downloading, and filling.”

A shared development and vision

Both Ultradent and Critical Manufacturing have excellent development teams. To facilitate innovation, they are building a joint development operations pipeline, which merges code from both parties into deployable packages that can be validated together.

“We wanted a partner, not a supplier, and that is very much what we have with Critical Manufacturing,” continued Pinegar. “Our MES roadmap looks about three years ahead and we have made a big change in how we will run this project by switching from a waterfall to agile methodology. For this to succeed, it is vital we take care of people and invest in them. Success lies in ongoing education and investment in all stakeholders at every level. We had never integrated IT and OT before, and we are learning from each other every day. But, gradually, MES is becoming the common language.”

A highly adaptable project team: You never know what is around the corner…

The first phase of the Ultradent MES project was hit with the COVID-19 pandemic. This precipitated a drop in business as dental offices around the world were forced to close. Through necessity, Ultradent put some projects on hold, but not the MES implementation. Core teams at Ultradent and Critical Manufacturing worked from home to deliver the pilot project on time, only entering the factory when necessary to interact directly with equipment or personnel.

Pinegar concluded: “The pilot line looks great and we are excited about the possibilities for the future. Critical Manufacturing has proved itself as an invaluable and adaptable partner and its MES gives us the flexibility we need to incorporate our own modules. Executives have seen the potential and are asking what it would take to roll out the MES everywhere in half the time! What we can achieve depends on many different factors.”

Additional advice from Craig Pinegar on delivering a successful MES project:

Back to topbutton